roller pass-through shot blasting machine, H-beam steel rust removal and cleaning machine

 

Usage Introduction

---

 

roller pass-through shot blasting machinecan work continuously and uninterruptedly, for all kinds of steel materials, such as steel plate, steel, steel beam, section steel, steel pipe and steel casting, etc., in a continuous way to remove oxide skin, cleaning and pretreatment, with the cleaning process cycle is short, the effect is remarkable and so on, really help users to achieve the goal of fast and efficient cleaning.

Universal roller pass-through shot blasting machineis suitable for shot blasting steel plates, profiles and small components, and can be integratedsteel pretreatment line.

steel plateSuitable for shot blasting steel plates, especially thin steel plates, which can be integratedsteel plate pretreatment line.

H-beam special through-type shot blasting machinesuitable for shot blasting H-beam and large components, can be equipped with painting, leveling, drying and other equipment.

steel cylinder and oxygen (acetylene) cylinder plateis suitable for shot blasting to clean steel cylinders, oxygen cylinders, acetylene cylinders, etc., and can be equipped with painting, leveling, drying and other equipment.

steel plate outer wall through type shot blasting machinesuitable for shot blasting to clean the outer wall of steel pipes with different pipe diameters.

Special through-type shot blasting machine for billetsuitable for shot blasting of round or square billets.

through type shot blasting machineis used to clean loose parts, which are put into special tooling for shot blasting.

round steel special through-type shot blasting machinesuitable for shot blasting of round steel.

Key Technologies and Assurance Measures

---

 

Workpiece conveying system

1. The variable frequency stepless speed regulation of the workpiece conveying system. Each work department can operate synchronously and independently.

2. The roller table of shot blasting room is equipped with special material wear-resistant sheath.

3, plate chain conveyor "V" type structure, after painting steel plate short line contact, in order to avoid paint film damage.

shot blasting

1. Photoelectric switch and brake motor are used for workpiece height measurement to prevent dust interference outside the shot blasting room.

2. The workpiece width measuring device automatically adjusts the opening quantity of the pill gate.

3, the use of advanced cantilever centrifugal shot blasting device, shot blasting device layout after computer simulation. The projectile shall avoid the roller table, and the workpiece shall be covered uniformly.

projectile sweep

rolling sweep, side sweep and high pressure fan blowing.

pellet cycle purification

1. Adopt full curtain winnowing separator.

2, the use of special polyester core hoist belt.

3. Adopt pneumatic projectile controller.

4. Each power point of the projectile circulation system shall be provided with fault alarm function.

shot blasting dust removal system

selection of cyclone, bag integrated dust collector, dust emissions to meet national standards.

Spray booth

1. Two high-pressure airless spray pumps, one of which is for standby.

2. Standard linear guide rail is adopted to support the trolley, and frequency conversion buffer is adopted at both ends of the trolley stroke.

3, the workpiece detection and transmission mechanism and spray gun separate set, no paint mist interference, easy to clean paint scale.

drying room

1, can use a variety of medium heater (or burner), hot air circulation, so that the heat can be fully utilized.

2, drying room temperature 40~70 degrees adjustable.

paint mist filtering device and harmful gas purification device

1, the use of advanced paint mist filter cotton filter mist.

2, the use of activated carbon adsorption of harmful gases.

electrical control system

1, PLC control, upper computer (microcomputer) dynamic simulation monitoring.

2. Circulating system fault alarm function.

3, wearing parts time accumulation timing function.

technical parameters

---

 

Q69 series roller table through type cleaning machine technical parameters

Specific Features

---

 

universal roller pass-through shot blasting machine

below cleanable 3500steel plates, sections and components
Shot blaster quantity 4-8
with workpiece upper surface projectile cleaning device
Configurable automatic loading and unloading device

steel plate

can clean the following 5000mm steel plate, thickness of more than 1.5mm

Shot blaster quantity 4-10

with workpiece upper surface projectile cleaning device

Add side sweep device

Configurable automatic loading and unloading device

H-beam special through-type shot blasting machine

cleaning H-beam range: 600~2400mm
The workpiece is allowed to have stiffened plate
Number of shot blasting device 6~12
can be equipped with sand scraping device
Can be equipped with the workpiece to take out the projectile recovery device

steel cylinder and oxygen (acetylene) cylinder plate

placing the workpiece on a slanted roller path through the shot blasting chamber

Number of shot blasting device 2~4

Because the workpiece rotates while feeding, and the roller table frequency conversion speed regulation, the cleaning effect is very good.

cleaning cylinder

steel plate outer wall through type shot blasting machine

the number of shot blasting device 2 power 55kw

cleaning steel pipe
conveyor roller table frequency conversion speed regulation
The shot blasting device is arranged under the chamber body, and the cleaning effect is uniform.

Special through-type shot blasting machine for billet

The section size of the cleanable billet is adjustable

Number of shot blasting device 4

shot blaster angle by computer simulation

cleaning effect is uniform

round steel special through-type shot blasting machine

cleaning round steel

For particularly fine round steel, a reflective plate is used to restrain the projectile.